Romulan Bird of Prey - 1/650 Vintage Recreation Display: Build Log #4

Greetings model builders!

Continuing on with the Bird of Prey...

Main Body - Painting 

Once I was happy with the filing of gaps, etc., it was time for me to move on to 200 grit wet sanding

I then moved forward with wet sanding the model with 400 and then finally 600 grit sandpaper.  Once I was happy with this, time to paint this bird!

The paint of choice for this build is Testors Light Blue in a rattle can.  Is this accurate to the filming model, absolutely no.  Is this model accurate to the filming miniature, no.  That's not my goal here, but to recreate a look and feel from the 70s and 80s from my youth, from what I saw hanging from the ceiling back then and this would have been the blue used.  

First Pass

I went over the model with paint for a first coat, not bad.

In the daylight, you can see a few flaws which are to be expected.  This paint is quite glossy so any imperfection is quite visible.

So another pass again of red putty and then sanding...

Also a problem where the pain peeled on the starboard side, most likely from not cleaning the area from sanding.  I had the same problem recently in a bathroom reno where the paint peeled off the ceiling in sheets...

Second Pass

I sanded again with wet 200 and 400 grit sandpaper and was a bit heavy handed with the paint but this model has few details (at this point) so it should mask a few sins.

I'm allowing time for drying between coats for the paint to cure.

That about wraps up this entry.  Below is a link to the previous entry, part 3.

https://fordosmodels.blogspot.com/2018/12/romulan-bird-of-prey-1650-vintage_5.html

Happy Model Building!

Star Trek and all related marks, logos and characters are solely owned by CBS Studios Inc. This fan blog (production) is not endorsed by, sponsored by, nor affiliated with CBS, Paramount Pictures, or any other Star Trek franchise, and is a non-commercial fan-made blog intended for recreational use.  No commercial exhibition or distribution is permitted. No alleged independent rights will be asserted against CBS or Paramount Pictures.

Romulan Bird of Prey - 1/650 Vintage Recreation Display: Build Log #3

Greetings model builders!

We last left off working on the main body assembly, refinements and the tail.  Now for the engines...

Nacelles

The nacelles on this model, like the rest of the model is really simple construction.

Upon looking at the aft end ports, you see straight back and can see the alignment pins, which are not aligned with the rest of the model.

To remedy this, I'm building my own using two pieces of styrene tubing and sawed off the old end from the nacelles.  The nacelle aft ends friction fit in the back.

Moving forward on the nacelles, they were puttied, sanded, primed and repeated.

I painted the inside black so that when you look down the aft end, you don't see the interior of the model.  This does deviate from my 'vintage' look but I feel leaving this as is would look sloppy.

Once I glued the nacelle to the wings/pylons, I laid up some more of the Evercoat to fill the gaps.

Further refinements...I will follow up with this in the next build entry.

The front end caps, or Bussard Collectors as they are known on Federation starships are 2-piece parts, with no locating pins.

Here are both parts for the nacelles glued up and ready for that process: fill, sand, prime and evaluate.

For the front 3/4 domes I drilled out a hole and inserted a screw to hold it for painting purposes.

After priming and sanding, I painted them with a craft gold colour.  The studio model I believe were blue/green which often appeared clear on screen due to the blue screen process.  I think it's a bit of a compromise with gold, but it give it that retro feel.

For the aft end tail pipes (lack of a better term) I went through a number of different silver/aluminum paint applications.

 

I ended up using a bright metallic paint by Rust-oleum.  Works for me in sticking with that retro look.

Original Kit Stand

The model stand which would have been originally supplied with the model is quite elegant, but has that distinct retro look, which I'm going here.  Unfortunately, there are markings on it, including the part numbers that need to be sanded off.

Easy assembly, just needs a bit of primer and black paint and it's done

That about wraps up this entry.  Below is a link to the previous entry, part 2.

https://fordosmodels.blogspot.com/2018/12/romulan-bird-of-prey-1650-vintage.html

Happy Model Building!

Star Trek and all related marks, logos and characters are solely owned by CBS Studios Inc. This fan blog (production) is not endorsed by, sponsored by, nor affiliated with CBS, Paramount Pictures, or any other Star Trek franchise, and is a non-commercial fan-made blog intended for recreational use.  No commercial exhibition or distribution is permitted. No alleged independent rights will be asserted against CBS or Paramount Pictures.

Romulan Bird of Prey - 1/650 Vintage Recreation Display: Build Log #2

Greetings model builders!

A little background on design of this ship...

The Romulan Bird of Prey, as first seen in Star Trek in the original episode, 'Balance Of Terror' as the guest ship in that episode.  It is fabled that in early drafts of the episode that the Romulans stole a Federation ship or a Federation design and had a big bright bird painted on the underside of the hull. That said, when looking at the main hull and another 'renegade' or stolen ship, it's hard not to un-see this...

USS Reliant on the left, Romulan BOP on the right

I've often wondered if the design of the Reliant was influenced but the BOP, hard to say but the original design (apart from reusing the Refit Enterprise and relabelling it as shown in early storyboards) had the nacelles above the main hull, much like the BOP.  I digress, onto the build!

The beginning...

Each time I build a model, I always start with a bath!

All plastic model kits are created from a mold and with every mold, there is a release agent that is coated in the mold so the plastic ejects easily.  This mold release can interfere with both paint and glue, so a good wash with dish soap and water deals well with this.

The BOP has a very simple assembly as seen below.

And here are all of the kit parts (including optional parts)

So, here is the Romulan Bird of Prey with all of its major sections glued up in sub assemblies.  

main hull, wings (port/starboard), nacelles (port/starboard), tail

Below is the BOP, mocked up.  Simple model, eh? (Don't mind me, I'm Canadian, lol)

So then I moved on to filling and sanding the sub assemblies, starting with the wings, or pylons if were a Federation ship.

Once I got that squared away, I glued them both to the main hull.

Here's my 'poor man's rig' with painters tape.  This is how I learned to build models as a kid and it works effectively.

Once the wings set, I put the nacelles on, to see their alignment.

As you can see, the nacelles aren't parallel with the main hull,

and the after portion of the nacelle is what will make this noticeable

Next step for me was to deal with the hollowness of the model.  The leading edge didn't quite meet between the two halves of the main hull (or saucer for lack of a better term).  This means I can't fill the gap without the filler popping out as the hull can flex.  My solution was to drill out the bridge section and use the hold to drizzle 15 min epoxy into the cavity.

I rolled the model around to coat the interior with the epoxy.  I did this in 4 passes: bow, stern, starboard and port sides.

Once the epoxy cured it was time to move onto the filling of the gap along the main hull.

\

For larger gaps where there can be flexing, I use a metal glaze by 'Evercoat'.  It comes as a two-part solution and like any chemical product, you should always use safety precautions protecting your hands with gloves, eyes with eye protection and use in a well ventilated respirator. 

What I like about this product is it cures quick and as it cures, you can us a hobby knife to slice off parts of it, minimizing sanding.

Next pass is to add primer, and then using Bondo spot putty to clean up the edge.

Yet again another pass.  I find it usually takes several (up to 3 to 4) passes of evaluate, putty, sand, prime, 'rinse and repeat'.  

Racing stripes??

No, the light coloured areas are basic plastic that was masked off where the nacelles and tail fin attach to.  Plastic adheres best to plastic, rather than glues.

To plug the hole, I drilled out a plug from a sheet of styrene and epoxied it in.

'

I ended up opening the stand hole in the bottom of the model and then drizzled more epoxy through it.  The painter's tape is to protect the model.  This hole will get plugged, but gets covered by the massive orange bird decal.  I've been using the Round 2 Dome Base stand to paint the model in the interim.

When I attached the tail fin, like many of these older models, I had to make a jig to keep it perpendicular to the hull as both halves of the tail aren't exactly even with each other.

one might recognize this as a Testor's liquid glue.

I also filled in any remaining holes in the bridge area with Apoxie Sculpt which is a 2-part putty that you kneed together and becomes as hard a rock when it cures, but sandable.

To fill all the gaps (not shown) around the tail, I used Evercoat Metal Glaze on it.

That about wraps up this entry.  Below is a link to the previous entry, something I'm going to start doing on these blogs.

https://fordosmodels.blogspot.com/2018/11/romulan-bird-of-prey-1650-vintage.html

Until the next time, Happy Model Building!

Star Trek and all related marks, logos and characters are solely owned by CBS Studios Inc. This fan blog (production) is not endorsed by, sponsored by, nor affiliated with CBS, Paramount Pictures, or any other Star Trek franchise, and is a non-commercial fan-made blog intended for recreational use.  No commercial exhibition or distribution is permitted. No alleged independent rights will be asserted against CBS or Paramount Pictures.